Furnace & heating
AC repair
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateRheem Heat Pump Service: The Fort Worth Owner’s Guide
If your Rheem heat pump is acting up, most repairs in Fort Worth run between $150 and $650 depending on the part that failed. We stock Rheem-compatible parts on our trucks, and we can usually diagnose and fix the issue the same day you call. That means no waiting a week for a part to ship while your house climbs past 90 degrees.
Here’s how most people find us: the thermostat says 72, but the air coming out of the vents feels warm. Or the outdoor unit is making a sound it never made before, a grinding or clicking that cuts through the usual hum. Sometimes the system short-cycles, kicks on for five minutes, shuts off, kicks on again. By the time you’re reading this, you’ve probably already checked the obvious stuff like the filter and the breaker. Good. That narrows it down. The next step is figuring out which Rheem part gave out and what it costs to fix it right.
Key takeaways:
- Most Rheem heat pump repairs in Fort Worth run $150 to $650 installed, part and labor included.
- We carry common Rheem-compatible parts on the truck: capacitors, contactors, defrost control boards, fan motors, and thermostats.
- Every repair gets a written price before we open a panel, plus a written guarantee. If it fails within the coverage window, the second visit is free.
- Book online, get a live arrival time, and track your technician to your door.
Which Rheem Models This Applies To
Rheem makes heat pumps under a few different model lines: the classic RP14 (14 SEER, single-stage), the RP15 and RP16 (mid-efficiency), the RP17 (two-stage), and the RP20 (variable-speed, high-efficiency). We service all of them. The model number is printed on a data plate on the side of the outdoor unit, usually on the back corner near where the refrigerant lines connect. It will look something like RP1430AJ1NA, with the first four characters telling you the series.
Here’s what matters when it comes to parts: Rheem uses a few proprietary components, especially on the variable-speed RP20 line. The inverter board on an RP20 is not interchangeable with a generic board from a supply house. On the single-stage RP14 and RP15, you have more flexibility. A quality aftermarket capacitor or contactor will do the job just as well as the OEM Rheem part, often at a lower price, and that’s what we quote most of the time. On control boards and defrost sensors, we lean OEM because those components talk to the rest of the system in Rheem-specific ways. If your unit is still under manufacturer warranty, we’ll handle the warranty part paperwork so you only pay for labor. Halden Heating and Air Fort Worth is an independent service provider, not affiliated with Rheem, but that independence is exactly why we can tell you when a generic part works and when it doesn’t.
Styles & brands we work with







Signs Your Rheem Heat Pump Is Failing
- Blowing warm air in cooling mode. This is the big one in a Fort Worth July. It usually points to a failed reversing valve, low refrigerant from a leak, or a dead compressor. The reversing valve is a Rheem-specific failure point, and not every shop keeps one on the truck. We do.
- Outdoor unit hums but the fan doesn’t spin. That’s almost always a failed capacitor, a $20 part that takes about 30 minutes to swap. Sometimes it’s the fan motor itself, which runs $200 to $350 installed.
- Short-cycling. The system starts, runs five minutes, shuts off, restarts. This is often a failing thermostat sensor or an overcharged system, but it can also be a compressor overheat switch doing its job. Either way, short-cycling shortens the life of the compressor, and the compressor is the most expensive part in the unit.
- Ice on the outdoor coil in summer. That’s not normal, and it’s not “just condensation.” It usually means low refrigerant, a failed defrost control board, or a blocked metering device. Running it like this for weeks can slug the compressor with liquid refrigerant and kill it entirely.
- Grinding or squealing from the outdoor unit. Grinding says the fan motor bearings are going. Squealing during startup says the compressor is struggling against a pressure imbalance. Both are cheaper to catch early than to wait until the part fully fails.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s the straight answer for Fort Worth, because you deserve real numbers before someone shows up at your door.
| Rheem Heat Pump Part | Typical Installed Cost (Fort Worth) |
|---|---|
| Capacitor | $150 – $250 |
| Contactor | $150 – $300 |
| Defrost control board | $250 – $450 |
| Fan motor (outdoor) | $300 – $550 |
| Reversing valve | $500 – $900 |
| Compressor (if covered warranty labor) | $400 – $800 |
| Compressor (out of warranty) | $1,500 – $3,000 |
Those prices include the part, the labor, and the diagnostic time. They do not include surprises, because we quote a written price before any work starts. Andre Fuller still remembers the first time a contractor handed him a surprise bill and he had to sit with it. That’s why Halden Heating and Air Fort Worth doesn’t work that way. Every repair comes with a written guarantee. If the same part fails inside the coverage window, we come back and fix it at no charge. That’s not an add-on you have to ask for. It’s included, automatically, on every job.
DIY or Call Us?
Here’s the honest split. Some things are safe to check. Others will hurt you or cost you more money if you touch them.
Safe to check yourself: the thermostat settings (make sure it’s on “cool” and the fan is on “auto”), the air filter (a clogged filter causes half the “my AC doesn’t work” calls we get), and the breakers (flip them all the way off, then back on). If the outdoor unit is iced over, you can turn the system to “off” and run the fan to thaw it, but that’s a temporary fix, not a solution.
Where DIY goes wrong: The capacitor inside the outdoor unit stores a charge even when the power is off. Touch the terminals and you’ll get a shock you’ll remember. The reversing valve and compressor run on 240 volts and refrigerant under pressure. Get either one wrong and you’re looking at a refrigerant burn or a $3,000 compressor replacement on top of whatever was originally broken. Heat pump service is not a YouTube-tutorial job. If the part that failed is electrical or involves refrigerant, call us at (817) 632-5499. We’ll send a background-checked technician with a live arrival time you can track to your door. Flat price up front, cool house by tonight.
FAQs
A well-maintained Rheem heat pump in Fort Worth typically lasts 12 to 15 years, but Texas heat accelerates wear on outdoor components like capacitors and fan motors, so expect to replace those every 4 to 7 years even if the overall system is still healthy. Call (817) 632-5499 for a realistic assessment of your specific unit.
Some parts, like control boards, can sometimes be repaired at the component level, but it’s rarely cost-effective after factoring in labor, and a repaired board won’t carry the same reliability as a new part with a written guarantee. We’ll always quote both options if a repair is feasible, and the estimate is free.
Most common repairs, capacitors, contactors, defrost boards, and fan motors, take 45 minutes to 2 hours once we’re on site, and we carry enough Rheem-compatible parts on the truck to complete the fix the same day in most cases. Call (817) 632-5499 and we’ll tell you whether your part is one we stock.
Yes, our trucks carry common Rheem-compatible parts including capacitors, contactors, defrost control boards, fan motors, and thermostats, so most Fort Worth repairs are done in a single visit. If your unit needs an OEM-specific part we don’t have on board, we’ll give you the honest timeline and a written price before ordering anything.
The general rule is the $5,000 test: if the repair cost multiplied by the age of the unit in years exceeds $5,000, replacement usually makes more sense, and a new system in Fort Worth runs $3,500 to $7,500 installed depending on size and efficiency. We’ll give you both numbers, repair cost and replacement cost, in writing, and let you decide without any pressure.
Written by Andre Fuller, Owner, Halden Heating and Air Fort Worth at Halden Heating and Air Fort Worth, serving Fort Worth and nearby areas.