Furnace & heating
AC repair
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateFast, Reliable AC Installation Across Southlake
Installing a new AC system in Southlake runs between $3,500 and $7,500 for most homes, and the job usually takes one to two days depending on how many systems you’re replacing. If you live in Southlake, you already know the challenge: large custom homes, multiple zones, and mechanical rooms tucked into attics where a sloppy install shows up as humidity problems six months later. Halden Heating and Air Fort Worth handles that complexity every week. Call (817) 632-5499 to get a written price before any work starts.

What makes Southlake different is the housing stock itself. Most of the homes we work in were built between the mid-1990s and mid-2000s, and many have two or even three full HVAC systems. When the original equipment fails, it tends to fail in clusters. One compressor goes in June, the other follows by August. That reality shapes how we approach AC Installation here: we plan for whole-home load, not just a single unit swap.
Why Halden Heating and Air Fort Worth Is Southlake’s Preferred AC Installation Company
Southlake homeowners rarely call for the cheapest bid. They call for a team that understands high-end construction, respects finished attics and custom millwork, and doesn’t leave condensers visible from the street. That’s the job we’ve been doing since 2004. Andre Fuller, who leads our team, built the company around one rule: put the price in writing before the first tool comes off the truck. No door-step adjustments, no vague “we’ll see what we find once we open it up.”
Every Southlake job includes a live arrival time you can track to your door. Not a four-hour window. A real person answers the phone 24/7, including at 2 a.m. when a 2003-era compressor finally gives up during a July heat wave. And because we’re part of the Relay Home Co. network, we’re held to The Relay Visibility Guarantee: every repair and installation carries a written guarantee, and if something fails within the coverage window, the second visit is free. No arguing, no fine print.
Styles & brands we work with







Central Air Conditioning Installation in Southlake
Central Air Conditioning Installation in Southlake is rarely a simple one-for-one swap. Most of the homes we serve in neighborhoods like Monticello, Timarron, and Carillon were built with high ceilings, large window banks, and multiple zone dampers that were state-of-the-art in 2001 but are now leaking and out of calibration. A proper installation here starts with a full Manual J load calculation, not a glance at the old unit’s tonnage. Skipping that step is exactly how you end up with a house that short-cycles in August, never reaches 72 on the west side, and holds 60% humidity even when the AC is running.
For most Southlake homes, central air installation lands between $3,500 and $7,500 per system, with larger two-stage or variable-speed equipment at the upper end of that range. The total depends on system count, duct condition, and whether we’re correcting airflow issues from the original build. Every quote includes a written price, an itemized scope, and a set install date.
Multi-Zone and Multi-System Design
Southlake’s large floor plans don’t respond well to single-zone thinking. A 5-ton unit on the main level and a 3-ton upstairs should be tuned as one system, with the thermostat calibration and blower profiles matched to actual room-by-room load. When we replace one unit, we check the other system’s static pressure too. A new high-SEER2 blower pushing against old, restrictive ductwork can be louder than the unit it replaced and never hit its rated efficiency.
Quiet, Concealed Condensers
Most Southlake HOAs and, frankly, most Southlake homeowners don’t want a condenser unit sitting in the sightline from the street. We routinely place or re-place equipment behind existing wing walls, in side yards, or on custom stands that keep it off the ground where debris collects. The equipment still needs airflow clearance, but there’s almost always a better spot than where the builder put it in 2003.
Furnace Installation in Southlake
Furnace Installation in Southlake usually happens in one of two situations: the furnace died during a winter freeze, or the homeowner is replacing the whole system and doesn’t want a mismatched 20-year-old furnace paired with a brand-new condensing AC. Either way, the job matters. Southlake’s periodic winter freezes, like the one that hit North Texas hard in February 2021, punish furnaces that were never properly sized for the home’s total heat load.
Furnace installation in Southlake runs the same range as central air: $3,500 to $7,500, depending on efficiency level and whether new venting or gas line work is needed. High-efficiency condensing furnaces with sealed combustion are the most common choice in Southlake because they can be installed in attic mechanical rooms without drawing combustion air from conditioned space, which is a real problem in tight, well-insulated custom homes.
Replacing Both Systems Together
If your AC and furnace were installed in the same year, they’re probably failing around the same time too. Replacing both at once costs more upfront but avoids a second labor charge later and lets us commission the entire duct system and control strategy as one integrated install. Southlake’s early-2000s mansions are now at the age where this is often the most honest recommendation we can make.

Attic and Closet Installations
Furnaces in Southlake tend to live in attics or dedicated upstairs closets. That means access is tight, decking has to be protected, and venting needs to route through roof penetrations without creating leaks. We use drop cloths, plywood work platforms, and floor protection runners on every job, and we photograph the workspace before and after so you can see exactly what we touched.
Trusted Brands We Service in Southlake
We install and service all major equipment brands, and for Southlake specifically we stock local parts for the units we see most: Trane, Rheem, York, and Daikin. Bryant equipment is common in the area too. Having the right parts on hand means faster turnarounds and fewer days without cooling when a capacitor or control board fails in the middle of summer. If you’re replacing a system, we’ll help you pick equipment by actual performance data for your home’s load, not by brand loyalty, and we’ll stand behind it with the 365-Day Done Right Promise on every completed job.
See the difference
Before
After
Before
After
Before
AfterCommon AC Installation Problems We See in Southlake Homes
- Undersized replacements that skip the load calculation. Southlake’s two-story custom homes with vaulted ceilings and west-facing glass need a real Manual J, not a tonnage match to the old unit. When a contractor skips that step, the new system never satisfies, the blower runs constantly, and humidity creeps up.
- Bad commissioning on multi-zone duct systems. The zoning dampers and bypass ducts from the early 2000s leak and fail. A new variable-speed system can’t compensate for a bypass damper that’s stuck open. We measure static pressure and room-by-room airflow before we call a job done.
- Wrong refrigerant charge on long line sets. Southlake homes spread out. Line sets run 60, 80, sometimes 100 feet. A tech who doesn’t weigh in the charge for that length of line set is guessing, and a guessed charge cooks compressors. We weigh in every charge to manufacturer spec.
- Condensers placed where pollen and debris choke them. Southlake’s tree canopy looks great and drops constant organic material. A condenser squeezed against a fence line with no clearance runs high head pressure and dies early. We reposition equipment for airflow and service access, not just aesthetic hiding.
Pricing for AC Installation in Southlake, TX
Here’s what a Southlake homeowner should expect to pay for common HVAC work in this market:
| Service | Southlake Price Range |
|---|---|
| Central Air Conditioning Installation | $3,500 – $7,500 |
| Furnace Installation | $3,500 – $7,500 |
| AC Repair | $150 – $650 |
| Furnace Repair | $150 – $700 |
| Tune-Up | $80 – $200 |
The biggest cost drivers in Southlake are system count, equipment tier, and ductwork correction. A straightforward single-system replacement in a smaller home lands near the bottom of the range. A full dual-system replacement with variable-speed equipment and duct repairs lands near the top. Every quote is itemized and in writing before we begin, and the price we quote is the price you pay. Call (817) 632-5499 for a free estimate.
We Also Serve Cities Near Southlake
Our crews work throughout the metro, so if you’re across the lake in Euless, up toward Keller, over in Haltom City, or deeper into Fort Worth, we can help. The same written-price guarantee and live tracking applies everywhere we go. AC Installation in Southlake is our specialty, but the surrounding cities get the same standard.
Serving Southlake, TX - Our Local Coverage Area
We’re based in the Southlake area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About AC Installation in Southlake
Because the original zoning dampers, bypass ducts, and control wiring from that era are now at the end of their service life, and a new high-efficiency system can’t perform correctly on failing zone infrastructure. When we replace one unit in a Southlake home, we check the whole zone system. If the dampers are leaking or the bypass is stuck, the new equipment never reaches its SEER2 rating and your upstairs still doesn’t cool right. Redesigning the zones at the same time often costs less than coming back later. Call (817) 632-5499 and we’ll assess what your system actually needs.
A properly sized and commissioned variable-speed system can hold Southlake’s summer humidity to around 45-50% without a separate dehumidifier, provided the blower profiles and thermostat calibration are set correctly. The catch is that undersized or oversized equipment, or a system with poor airflow, won’t pull enough moisture out of the air no matter how efficient the rating. Our crew recently commissioned a dual-system replacement in Monticello and verified the home held 45% humidity at 98°F. That’s the difference between a real install and a swap-out.
Commissioning is the verification phase after installation where we measure static pressure, set blower motor profiles, calibrate the thermostat, and confirm the refrigerant charge by weight. In a Southlake attic mechanical room, skipped commissioning is why two identical-looking installs can deliver completely different comfort. We measure and document every system before we leave, so you know what the equipment is actually doing, not just what the brochure promises.
We place condensers behind wing walls, in side yards, or on low-profile stands that keep them out of street sightlines, and we route line sets through chases, soffits, and attic paths that avoid visible exterior runs. Attic equipment gets installed on isolation pads to prevent vibration transmitting through framing. Southlake’s custom homes were designed to hide mechanical systems; the original builders just didn’t always follow through. We do.
We recommend coil guards or hail guards on the condenser, regular washing of the outdoor coil, and a maintenance schedule that includes coil inspection at least twice a year. Southlake’s tree canopy means cottonwood, oak pollen, and leaf litter accumulate on coils faster than in open-lot neighborhoods, which raises head pressure and shortens compressor life. During installation we also make sure the unit sits high enough off the ground that grass clippings and mulch don’t get pulled in.
Written by Andre Fuller, Owner at Halden Heating and Air Fort Worth, serving Southlake and the surrounding metro since 2004.